Dusty Motors justerbart beskyttelsestrekk i svart i ekstra stor størrelse. Passer karrosserilengder på 35-37cm.
Dusty Motors beskyttelsestrekk er laget for å holde innsiden av din radiostyrte bil så ren som mulig. Utrustet med glidelås for enkel tilgang til elektronikken.
Product details in english
Universal Shroud Cover
This is a high quality, hand made, dust and water splash proof shroud, designated to fit a various different RC models by those manufacturers: HPI, Kyosho, Team Associated, LOSI, Tamiya, Traxxas, Thunder Tiger, Ofna, Tekno, Mugen, XRay, Axial and etc. Shroud comes with a zipper, which allows to access the internals of a model i.e. connecting/disconnecting batteries and turning a model on/off without removing a shroud. While taking a brake between the running stints the shroud can be unzipped to allow ESC and motor to cool quicker. Shroud is made from the highest quality materials. That is why it is strong, durable and efficient. The open area of a material is more than 50% of total shroud surface, so it ensures a very good air flow in order to keep the model electronics cool.
Shock absorber cover is included into the package. Shock absorber cover comes in one long piece, so it could be cut into lengths that particular shock absorbers require. Cover is made from elastic material in order to fit shock absorbers of different diameters. Two included lengths of a cover will be enough for 8-16 shock absorbers, depending on a length of one.
How to choose a right universal adjustable shroud:
1. Check a chassis of your model for the spots to glue a Hook & Loop Fastener tape. For the best result Hook & Loop Fastener should be applied to a vertical sides of a chassis. Glued Hook & Loop Fastener should cover all length of chassis, from a front shock tower to a rear one, i.e. shroud side should cover all chassis side.
2. Measure the length of one side of chassis. According to a measurement results choose one of six sizes of universal shrouds.
Shroud comes with a zipperAdjustable front ant backSix different sizesFor models from 1/16 up to 1/8 scaleGenuine adhesive Hook & Loop Fastener® tape includedShock absorber cover includedHand made with a very strict quality inspectionEasy installationMADE IN EUROPE
Before applying Hook & Loop Fastener® to the chassis, cut the tape to the necessary length and width. For example, to place Hook & Loop Fastener® tape on an old Slash 4×4 nerf bars, you must cut it in both directions: length and width.
Make sure that the surface of the chassis is extremely dry and clean before applying the Hook & Loop Fastener® tape. Dip a napkin in pure alcohol and clean the surface of the chassis. (Use vodka if you like, but for best results, do not drink the vodka during the process).
Let the Hook & Loop Fastener® tape adhere to the chassis for 24 hours before you use the shroud.
If it?s hot outside, leave the Dusty Motors? shroud unzipped to promote airflow and help keep the electronics cool. Even when bashing with a unzipped shroud, it will still keep out most of the dust and debris.
When it?s hot outside ? or if you have a car gearing set up that?s capable of reaching the speed of light ? be smart when you bash. Don?t let the temperature of the electronics get too hot. Take breaks between rides. Unzip the shroud and let the model cool to a normal temperature.
When bashing in winter, don?t bring your model into a warm room without removing ice and snow from the shroud. Otherwise, the snow will melt and water may penetrate the shroud and get into your model electronics.
Do not drive under water. It is a CAR, not a submarine, and the Dusty Motors shroud is only made for cars. Our shrouds are good, but they can?t be breathable and 100 percent waterproof at the same time. Physics just doesn?t work that way. The splashes of water are OK, so don?t be concerned if the shroud gets a bit damp.
Remember to take care of the shroud. Wash it by hand with warm, clean water. Let it air dry, do not put it in a dryer.
Mer info på Engelsk