HjemBilerElektrobilerElektrobil Touring, Asfalt
Print produktark

CRC MetriCKs Carpet Knife 1/12 Pan Car Kit

Produsent Calandra Racing Conceptc Inc.
Tilhører kategori
Elektrobil Touring, Asfalt
Handle nå, del opp eller betal senere. Walley Les mer
kr 4.495,-
Kjøp
Overvåk
+
-
Husk i favoritter
3|4|249
VareID: 65563, Produktnr: 3000
LoadWalleyWidget
Produktinfo
Anbefalt tilbehør
Deler
Tips en venn
Anmeldelser

Produktinformasjon

1/12 Pan car
LCG
Konkurransebil
CRC MetriCKs Road Race 1/12 Pan Car Kitt er en 1/12 innendørsbil beregnet til konkurranse . Bilen leveres uten elektronikk og karosseri og dekk som passer din bane!

Anbefalt tilbehør

  • Rask og effektiv i svinger
  • Lavt tyngdepunkt
  • Enkelt design, enkel å bruke
  • God holdbarhet
    • Product details in english
    In the front, the MetriCKs features CRCŽs Ultra-tune suspension. Just change the lower C/C plate (caster/camber plate) and your caster and camber are perfectly set. A "4 -1" plate gives you 4 degrees caster and -1 camber. Switch to the 5 -.5 plate and you have 5 caster and negative .5 degrees of camber. Go smash a bunch of barriers, and your caster + camber settings are still the same. We will have a plethora of different combinations available. And this is from Team CRC, so the price for optional C/C plates will be affordable. Throw your expensive setup gauge in the garbage, you wont need it.

    With a simple and quick change of the C/C plate (caster/camber), you can set caster and camber with precision and ease. No setup station, no guessing, no fiddling. Perfect camber and caster is machined into the pieces.

    Speaking of smashing into barriers, a new, flexible 3d printed bumper will help you bounce off the barriers mentioned above. The open design of the bumper increases front downforce.

    We have 6 different front springs available for the car. Ranging from .4mm to .65mm, these springs made with precision from the best material available. The springs will mount over the CRC straight 5mm king pin and should fit other cars as well (A12 and Prodigy).

    The Ultra-tune front end uses the durable 1/8 x 5/16 wheel bearings. These bearings are much stronger than the 3/16 x 5/16 bearing found on many other cars.

    The front mounted side-to-side roll springs separate the roll stiffness from the center/bump stiffness. For those traditionalists that like the side springs in the rear, there is a provision to mount the side roll springs in back. The MetriCKs features an easy to adjust rear center spring for preload, setting battery height and bump stiffness.

    Super easy battery height and droop adjustment. From the top, with a simple hex head, the center preload is adjusted to alter the amount the car "sags in" when race ready. From the bottom of chassis, a simple twist of a wrench on the limit set screw adjusts the "extension" or down travel of the car. Super easy to see and adjust.

    Another goal is low center of gravity. With the MetriCKs, the tungsten weights fit LEVEL with the chassis bottom, not stacked on the chassis or battery plate. We put the ballast at the very lowest position possible. Literally on the same plane as the bottom of the car. Because this car is so lightweight (needing lots of weight) and the ballast is so low, the center of gravity of this car is extremely low. Speaking of tungsten weight, we will have it available, but it is a common tungsten ballast available in many hobby stores, super affordable and easy to get. Keeping with the CRC tradition, high performance at a great price

    Dual linear dampers are super easy to set, change and maintain. The reservoir of damping grease is protected by an easy-to-remove seal from above. Using a line a diff/damper greases (preferred over silicone fluids), the dampers are leak free and easy to maintain and keep consistent.

    The dampers features a large volume reservoir to hold damper grease.
    The car features super strong, precision machined motor plates with a very low center of gravity. Two locking hubs clamp onto a lightweight differential axle which makes is less costly to switch to a differential. Just add a diff hub and bearing to affordably switch to a differential, perfect for the popular GT12R class.

    The new MetriCKs finished 1-2-3-4 at the 2024 Canadian Nationals in 13.5 Super Stock. In the stock class, a solid 1-2 finish matches the same 1-2 finish as the 2024 Snowbird Nationals. The car is already a proven winner!

    Durable, affordable, now with all metric hardware, the new MetriCKs is a proven winner. Pre-order your car today! Shipping before September 1, 2024 (we think it will be even sooner).
    Mer info på Engelsk

    Anbefalt tilbehør

    MyLaps RC4 Hybrid Transponder Bil/Båt
    3|32|625
    kr 1.795,-
    1s 8000mAh - 55C - Sunpadow Platin Shorty
    3|5|312
    kr 695,-
    1s 8500mAh - 130C - Aerox Hardcase
    3|3|312
    kr 945,-
    1s 7400mAh - 160C - Aerox Hardcase
    3|4|312
    kr 995,-
    Hobbywing XeRun V10 G3 6.5T OnRoad Spec
    3|6|561
    kr 1.149,-
    Sanwa Radio MT-5 m/RX493i 2.4GHz 4ch
    3|6|719
    kr 3.895,-
    Protoform AMR-12 Lightweight 1/12 Body Ulakkert
    3|44|1139
    kr 349,-
    Hobbywing XeRun XR10 Pro HD 120A V4.1 ESC 1s
    3|5|42
    kr 2.395,-

    Produktanmeldelser

    Desverre ingen tilbakemeldinger på dette produktet enda.

    Gi din tilbakemelding
    Produkt
    CRC MetriCKs Carpet Knife 1/12 Pan Car Kit
    Velg karakter
    Overskrift
    Produktanmeldelse
    Logg inn her
    Retningslinjer
    Produktanmeldelser er ment for at du skal dele din erfaring med andre som søker kunnskap om produktet.
    Urelevant, uriktig eller støtende innhold vil bli fjernet.

    Spørsmål, reklamasjoner e.l: kontakt oss direkte
    Flere så også på



    100% norsk nettbutikk
    Om oss

    Lynrask levering
    Les mer

    60 dager bytterett
    Gå til bytte & retur
    Prisjakt
    Kundeomtale på prisjakt
    Les våre omtaler